The Round Table (Rational Pagans Forum)

Science & The Supernatural: A Discussion of the World Around us - Based on Science with an Interest in the Supernatural ...
It is currently 18 Nov 2017, 05:27

All times are UTC - 5 hours




Post new topic Reply to topic  [ 1 post ] 
Author Message
PostPosted: 13 Nov 2017, 21:23 
Offline
Second-Sight Apprentice

Joined: 03 Jul 2017, 05:28
Posts: 260
You may need to remove all the components from a printed circuit board for rework Wholesale Jerseys China , repair, upgrade, salvage or other purposes. But how do you do it in the most efficient way? It’s a simple process if you keep in mind that most printed circuit boards (PCBs) have both active and passive components that are attached to the PCB in one of two ways: surface-mounted or through-hole.

Surface mounted devices (SMDs) are electronic components that are soldered to the PCB surface by their miniscule metallic surface terminals. Common examples of SMDs are passive parts such as resistors are capacitors, or active parts such as ICs.

Through-hole components have leads that are inserted through padded holes and are then soldered to the pads on the bottom side of the PCB. Common examples of through-hole components are resistors, capacitors, relays, inductors, transformers and more.

To remove SMDs and through-hole components from a PCB Wholesale Jerseys , use the following procedure:

Preparation

1. Don personnel protective equipment (PPE) such as safety glasses and gloves.

2. Set the PCB on a work surface that is both horizontal and dry. It is important that the PCB is set on a truly horizontal surface; when the PCB is heated, molten solder will be created and may move to adjacent pads or tracing when set on a non-horizontal surface, which may cause short circuits on the PCB.

Removing SMDs

3. Use a heat gun to remove the SMDs. After turning on the heat gun, position it approximately 15 centimeters above the PCB with its nozzle pointed down. In short order, the heat will melt the solder flux of the SMDs that are beneath the nozzle of the heat gun. Quickly remove these components by utilizing a tweezers. Collect them in a tray. Repeat this procedure until all the SMDs are removed from the top side of the PCB.

4. After you have removed all the SMDs, allow the PCB to cool for up to three minutes. Power down the heat gun and properly stow it away in a safe place.

Removing Through-Hole Components

5. Energize a soldering iron and sets its temperature to 450oC. Obtain a 6-inch length of copper desoldering braid.

6. Select a desoldering starting point at the far edge of the board. Then touch the copper braid on top of a pad that as you place the tip of the soldering iron on the solder joint pad. In a matter of seconds, the solder flux should melt and flow into the copper braid. Follow this procedure for all pads.

7. After you have completed desoldering on the pads on the reverse side of the board, flip the PCB over and repeat the process again using both the heat gun and the soldering iron to remove any other components and residual solder.

8. When all SMD and through-hole components are removed Cheap NBA Basketball Jerseys , de-energize the soldering iron and properly secure it in a safe location.

Clean Up

9. Inspect the PCB and using swabs doused in alcohol, clean the pads on both sides of the PCB. After you have cleaned the pads, you should have removed all the components from the PCB. Insulation is one of the first advantages most people are looking for when it comes to flooring. Even if you want to keep your home connected to the outside environment, you are looking for the best ways to keep it separate at the same time. As a result most homeowners look to installing double glazing windows, and insulate the walls as well as the roof on top.

One of the things to keep in mind is that the floors of your home should also provide quite a bit of insulation. If you have a basement and you want to turn it into living space, then it takes planning to be sure you will enjoy the right amount of comfort there. This is why you must find the best basement flooring that will serve the purpose you had in mind.

The first and most important aspect you should consider is the heat insulationretention. If you want to enjoy this part of the house the same as the rest, then the best basement flooring will not only work to keep the cold out, but is going to feel warm as you walk around on it too. You should not be forced to wear shoes or slippers to go about the basement.

This part of the house can be used for a wide range of purposes after you install the best basement flooring. You can use it as a space to entertain friends Cheap Basketball Jerseys , create an apartment for extra rent money, or even a rehearsing spot for your band. And even though you generate quite a bit of noise, with cork flooring and walling, the rest of the house will not suffer because of this.

If you do not want to make any compromises after you renovate the basement, you can install soundproofing floors in the rest of the house as well. As long as it will offer acoustic insulation for all the other rooms, you can use that space for any purpose you had in mind. If you convert it into living space, the floor also reduces the noise of your footsteps.

Soundproofing floors can be used in apartments as well. Many buildings have very thin walls and floors and noise can travel from one apartment to the other with little effort. If you use the right materials, you will be able to insulate your apartment from the rest and vice versa. But where will you find the right insulation floors for your home?

A single product can offer the acoustic insulation properties you are interested in combined with heat insulation Cheap Nike NBA Jerseys , comfort for your feet and it will not make any compromise when it comes to design. If you want to find the best product on the market today, cork floors should be at the top of the list from the start. No matter if you want to install soundproofing floors in a house or in an apartment, you will be able to find the best answers at icorkfloor. Visit us today.


Dog Training For . Wholesale NFL Jerseys Wholesale Jerseys Wholesale Jerseys From China Cheap NBA Jerseys Cheap Jerseys From China Cheap NFL Jerseys Cheap NFL Jerseys China Wholesale NFL Jerseys China Wholesale NFL Jerseys Wholesale Football Jerseys


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1 post ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 21 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group